・Multi remote

AR32-E・AR33-E
AR34K
AAR202
RC-22AC
OAR-N9
OAR-N11
Setting AR32-E/AR33-E
●Automatic setting(For each manufacturer code)
①Put the remote towards the main unit.
②Press and hold 【設定】 button.(Manufacturer code searching starts after 5 seconds.)
③ The number starts going up from "000". Please release 【設定】 button when you see the main unit starts operating.
※If you lost the timing to release 【設定】 button, you can return to the number with 【温度▼】 button.
④Press 【設定】 button again, and setting is completed.
●Manual setting
①Press 【設定】 button for 2 seconds and release, you can see 3 digits number blinking at the right bottom in the screen.
②Please set manufacturer code with 【温度▲】 or 【温度▼】 button.
③Check the main unit is operating, press 【設定】 button.
Setting AR34K
●Automatic setting (For each manufacturer code)
①Put the remote towards the main unit.
②Press and hold green 【運転 button】, and release when you see a manufacturer code on the display.
③ Please wait untili you hear beeping sound since it starts operating.
④When it's beeping, press 【設定 button】 to stop searching.
※If you lost the timing to press 【設定 button】, please return to the code with 【温度▼】 button. When it beeps again, press 【設定 button】.
●Manual setting
①Press 【設定 button】 for 2 seconds, 3 digits number blinking at right bottom in the screen.
※If you press and hold 【設定 button】 more than 5 seconds, it becomes time setting.
②Press 【温度▲】 or 【温度▼】 button to set the manufacturer code.
③Please check the main unit is operating, and finish with 【設定 button】.
Setting AAR-202
●Automatic setting(For each manufacturer code)
①Put the remote towards the main unit.
②Press and hold 【設定】 button and 【電源】 button for 4 seconds.
③ Temperature display becomes "00". (There might be another number, but it is not malfunction.)A transmitting mark turns on.
④Please release all buttons when a transmitting mark turns on.
⑤Automatic search starts as a transmitting mark blinks. (Once in 3 seconds)
⑥When the main unit turns on, press any button on the remote. A transmitting mark turns off, and search is completed.
●Manual setting
①Press 【設定】 button for 2 seconds.
②Temperature display becomes "00". (There might be another number, but it is not malfunction.)
③Press and hold 【設定】 button, set the manufacturer code with 【温度▲】 and 【温度▼】 button.
④Please release all buttons as setting is completed.
Setup steps RC-22AC
●Setting method
① Holding down [ OFF切/ON入 ] then press the button corresponding to the manufacturer for the setting (cooling 冷房/heat暖房 / dehumidifying 除湿/automatic自動)
[ OFF切/ON入 ] +[cooling 冷房] Daikin / Sharp / Chofu
[ OFF切/ON入 ] +[heat暖房 ] Panasonic (National) / Sanyo / Hitachi
[ OFF切/ON入 ] +[dehumidifying 除湿 ] Toshiba / Corona / Fujitsu General / Funai / LG Electronics
[ OFF切/ON入 ] +[automatic自動]Mitsubishi/ Mitsubishijūkō (Beaver)
② 2-digit setting code flashes on the LCD screen. Press the [Temperature ▲ / ▼] button to select 2 digit code. * Press and hold the button to fast forward. (There is a maker code list below)
③ When the code for setting is displayed on the LCD screen, complete the setting pressing [ OFF切/ON入 ] button again.
Setup steps OAR-N9
●Setting method
① Holding down [ OFF切/ON入 ] then press the button corresponding to the manufacturer for the setting (cooling 冷房/heat暖房 / dehumidifying 除湿/automatic自動)
[ OFF切/ON入 ] +[dehumidifying 除湿 ] Panasonic (National) / Sanyo / Hitachi
[ OFF切/ON入 ] +[cooling 冷房] Mitsubishi/ Mitsubishijūkō (Beaver)
[ OFF切/ON入 ] +[heat暖房 ]Daikin / Sharp / Chofu
[ OFF切/ON入 ] +[automatic自動] Toshiba / Corona / Fujitsu General / Funai / LG Electronics
② 2-digit setting code flashes on the LCD screen. Press the [Temperature ▲ / ▼] button to select 2 digit code. * Press and hold the button to fast forward.
(There is a maker code list below)
③ Push the operation button towards the air conditioner and check whether the air conditioner works.
④ In the same manufacturer, there are multiple codes, please try in order.
Setup Guide OAR-N11
● Configuration method
① Press the start/stop button first【運転/停止】, then press at the same time wind intensity and operating mode buttons fir about 2 seconds 【風量】【運転切換】
② While facing the air conditioner, set the air conditioner code by using the up and down arrows for temperature 【▲温度▼】
※【▲温度▼】The code will change each time you press the up and down arrow button.
※【運転/停止】The code will change automatically when you press the start/stop button.
③ First press timer off button【タイマー切】and then wind direction button【風向】for finalizing the setup.
manufacturer number file
manufacturer number file (RC-22AC.OAR-N9).pdf